Sea&Sea MDX-7D Instruction Manual

取扱説明書Instruction ManualCanon EOS 7D Mark II06175MDX-7D Mark IIUNDERWATER HOUSING for日本語English

E-91CAUTIONOpening and Closing the HousingOpening the locking latchesWhen removing the locking latches, be sure to use the tips of your fingers, not

E-10Opening and Closing the HousingCAUTION12Closing the locking latchesAlign the front case with the rear case and press them togetherFirst, put the

Attaching and Detaching the Port E-11Only the optional ports designed for SEA&SEA digital SLR camera housings can be attached to this product.Po

E-12Attaching and Detaching the PortDo not attempt to remove the port with the port lock lever in the position. Doing so could damage the qui

E-13Mounting the Camera in the Housing Make sure to remove the eyecup from the camera. If used with the eyecup in place, it could cause flooding.Rem

E-14Mounting the camera in the HousingAlign the quick lock with the LOCK position to fix the camera in place67Align the front case with the rear case

E-15Connecting the StrobeWhen using external strobe(s) with this housing, ensure to use the appropriate sync cables and converter, depending on your n

E-16External ControlsPower switchBy rotating the knob as shown, you can turn the power ON/OFF and operate the illumina-tion switch.Focus / Zoom dialWh

External ControlsE-17Push the lever to operate them.The strength of the spring for the shutter lever can be changed by adjusting the position of the s

External ControlsE-18Other controlsCAUTIONAfter mounting the camera in the housing, make sure to check that all of the housing's control parts w

E-1Note: Introduction Contents Thank you for purchasing SEA&SEA products. Please read this instruction manual carefully prior to using this produ

External ControlsE-19Unauthorized disassembling and/or modification could result in malfunction or flooding, and void product warranty. Take the pro

E-20Sync connectorCordWith the Optional Sync Cord 2-pin Connector (50122) installed in the connector hole, you can connect SEA&SEA strobe sync cor

External ControlsE-21ArmMDX-7D Mark II dedicated housing built-in YS converterRibbon to lift batteries outA Optional YS Converter / C1 can be attached

FinderE-22Attaching the Optional Accessories12CAUTIONReplacing the pick-up finderRotate the finder unit mounted on the rear case in a counterclockwise

E-23Connecting the StrobeAttaching the Optional AccessoriesConnect the strobe with the fiber-optic cable (option) when the strobe is triggered by sens

E-24CAUTION21When the strobe is triggered by sensing the light from the camera's built-in flash, the light from the built-in flash may be exposed

Attaching the Optional AccessoriesAccessory shoeE-25<Example>CAUTIONStrobes / lights can be mounted to the accessory shoe by using optional Mini

E-26CAUTIONMaintenance and StorageAfter rinsing, dry the product well with a soft dry cloth, then let the product dry in the shade, out of direct sun

E-27SpecificationsCompatible cameraCanon EOS 7DmkⅡControlsConstructionBody: Corrosion-resistant aluminum alloyGrip: Corrosion-resistant die-cast alumi

Memo

E-2WARNINGCAUTIONSafety PrecautionsWARNING Situations that could result in severe injury or death. CAUTIONSituations that could result in property dam

1445-Z-01A(2015年2月現在 / Current as of Feb.2015)シーアンドシー・サンパック株式会社〒145-0062 東京都大田区北千束1-4-6TEL.03-5701-5533カスタマーサービスセンターTEL.048-255-8512http://www.seaands

E-3Safety PrecautionsDo not rest heavy weight on the product. It might deform the outer casing, damage internal parts, make the waterproofing fail,

E-4Precautions on Handling the O-ring CAUTIONAre there any scratches or cracks in the O-ring? Be careful about dust, sand, and hair SEA&SEA produ

E-5Silicone grease protects the O-ring from chafing. After checking the O-ring to make sure that there are no scratches, dust, or debris, apply a ligh

E-6Identification of PartsPort lock leverFiber-optic cable socketAccessory shoeConnector holeMain-command dialShutter leverGripMetering mode selection

E-7Rear caseLeak sensormain bodyPick-up finderIdentification of PartsFront caseQuick shoeQuick shoe baseQuick lock

Preparation for Setting UpPrepare the housing and portPrepare the digital cameraE-8This product must be used in combination with the optional equipmen