INON Z-220 Underwater TTL Auto-Strobe User Manual Thank you for purchasing the Inon Z-220 Strobe. The Z-220 is an underwater TTL strobe with 22 Gu
New-Z(electrical) 5 U 6 Old-Z X 2 X 2 LG/L 5 U 6 G/New 3, 5 U 6 First Inon Model X 4 X 4 F90/F100 Nikon 5 U 6
Confirming the connection method Next, confirm the strobe to camera/housing connection method. For more information on parts for optional connectio
Connecting Z-220 to Strobe Arms The Z-220 can be adapted to many types of strobe arm systems. The Inon “Z Adapter” is a ball adapter part specially d
On Inon housings, when the shutter is released the Target Laser automatically shuts off so no laser light is recorded in the image. On Inon housings,
21. Magnet 22. Magnet Screw Tightener 5. Optical Sensor With Inon housing systems connected to the Z-220 with optical cable, the Optical Sensor senses
Lamp turns red and buzzer sounds when strobe charge complete. 12. TTL OK Green Lamp / Buzzer When the strobe is set to TTL mode, the lamp tur
Then screw down the Magnet Screw. Caution: Screwing down the Magnet Screw too tightly will damage the strobe. Use the “Magnet Screw Tightener” as
Connecting to Camera or Housing System Connecting with Electrical Cable (Sea & Sea Syncro Cord / N) 1) First, refer to the Sea & Sea Syncro
Using the Z-220 Main Switch functions and use method OFF Turns off Z-220 power. A Q OPTICAL & SLAVE Set to this position when Z-220 connected t
Setting Main Switch and Laser Switch Positions for different camera systems Determine the proper switch setting to use different strobe functions base
period, for manufacturing defects or repair matters where the strobe has been subject to normal use; and, when operation, handling and maintenance hav
Note: When using the integral strobe of digital cameras as the master strobe, setting the switch to TTL will not result in TTL exposure. Setting the
(**) cont. Also, when the batteries are near exhaustion the voltage level tends decreases, and the actual strobe output may be slightly less than
4) Do not leave the strobe closed when traveling to or from high altitudes, including travel on aircraft. Always remove the Battery Box Cap. 5) Whe
3) Take care to wash especially well the Optical Sensor. If salt is allowed to buildup, it may cause the clear resin portion to become hazy and prev
Attach to Z-220 Optical Sensor so light can only enter the sensor from one direction. After 7) O-rings, contain lubricant in the o-ring rubber. Ye
Depth Rating: 100m (330 feet) : Diameter: AppSize rox. 100mm : 100mm eight: ir: tteries /W: h 4 AA Nicad batteries) ght: atically turns on when
Quick rehe Z-220 can only be used in slave mode with digital cameras. Automatic TTL synchronization . m 11 to 4). verhaul he Z-220 is designed and
INON Z-220 Manual Version 1.41 Dec. 24, 2002 Translation Copyright 2002 by Mark Rupert 27 Pleon Dealer Contact Information: ase consult with Inon
Connector Cap O-ring Connector Cap O-ring groove Sync connector O-ring contact surface Sync cord O-ring Sync cord O-ring groove O-ring insp
visible it is ok to lightly grease the O-ring while it is seated in the O-ring groove. For other maintenance follow the instructions below. Removing
Z-220 Part Names INON Z-220 Manual Version 1.41 Dec. 24, 2002 Translation Copyright 2002 by Mark Rupert 5
1. Flash Tubes 2. Focus Light 3. Target Laser 4. Target Laser Cover Switch 5. Optical Sensor 6. Main Switch 7. Mode Switch 8. Camera Type Switch 9.
Z-220 Features The Z-220 is a high performance, multi function TTL strobe with many features. Depending on what camera system and master strobe the
Note: The Optical Sensor is extremely sensitive to light. The strobe may not function consistently in very bright conditions as the Optical Sensor
X1-G NEW X1 X1 (w/new circuit) G/New Inon (Canon) (cont.) X1 First Inon Model F90 Series, F100 F90/F100 Nikon other than F90, F100 Nikon Nikonos
Comments to this Manuals